Apple is developing a set-top box to support Bluetooth and NFC

According to the FCC's product supervision database, Apple is still developing a device that supports NFC access communication technology. This is also the first time since September 2016 that rumors have surfaced.

Apple TV experience enhancement: TV did not finish watching and picked up the iPhone to continue broadcasting

The data on all regulatory labels is almost the same, except that the SKU has changed from JR2 to JR1, and EMC has also changed from 3133 to 3137.

As with the previous version of the device, this device has an average current of 100mAh, at the same time, up to 700mA and a voltage of 5.5v to 13.2v. At the same time, the document also mentions Bluetooth and NFC incoming communication technology, but it does not include Wi-Fi. So it is possible that an apple is redesigned or there is no Wi-Fi connection.

As mentioned in previous reports, this set-top box-like product is similar in appearance and size to Apple TV, but it is not exactly the same from other parameters. At present, Apple has not made any comment on this device. However, since the list of information on the FCC has always been very small, it is still not possible to obtain accurate answers on what exactly this device is.

Fingerprint Lock Motor

Fingerprint Lock Motor introduction:

Basic security work, lock body responsible for the security door lock body responsible for opening and closing lock, the lock body Lock Motor is of crucial importance.

Functions: it is widely used in various intelligent locks, such as Shared bicycle lock, fingerprint lock, glass lock, safe lock, hotel lock, family lock, inductive smart lock, etc

Features:Fingerprint Lock Motoris based on micro precision reducer development, small intelligent micro precision reducer can do 10 mm in diameter, is widely used in safe, locks, smart locks, sensor intelligent lock;

This kind of motor has the characteristics of low noise, low energy consumption, small volume, light quality, high precision, large torque and durability

Method of use: the best stable in horizontal plane, installed on the Fingerprint Lock Motoroutput shaft parts, cannot use a hammer to knock, knock prone to press into the dc Fingerprint Lock Motor drive, may cause damage to internal components, and cannot be used in the case of blocked.

Operating temperature range:

lock motor should be used at a temperature of -10~60℃.

The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.

If a lock motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.

Storage temperature range:

Fingerprint Lock Motor should be stored ta a temperature of -15~65℃.

In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.

Service life:

The longevity of Fingerprint Lock Motor is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.

●Use with a load that exceeds the rated torque

●Frequent starting

●Momentary reversals of turning direction

●Impact loads

●Long-term continuous operation

●Forced turning using the output shaft

●Use in which the permitted overhang load or the permitted thrust load is exceeded

●A pulse drive ,e.g.,a short break,counter electromotive force,PWM control

●Use of a voltage that is nonstandard as regards the rated voltage

●Use outside the prescribed temperature or relative-humidity range,or in a special environment.

●Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.

when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you

Looking forward to your inquiry. Welcome to our factory.

Fingerprint Lock Motor,Motor For Fingerprint Lock,Gear Motor For Fingerprint Lock,Dc Motor For Fingerprint Lock

Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com